DoP DECLARATION OF PERFORMANCE Nr: 1. Unique identification code of the product type: VIKING 800 2. Type, batch or serial number of the product: VIKING 800 DESCRIPTION OF THE PRODUCT Type of application Underlay sheet with self bonding edges Method of application Mechanical with self bonding edges Type of coating SBS-modified bitumen Type of carrier Net reinforced polyester non woven Type of top surfacing Fine sand Type of bottom surfacing PP-fleece Mass per unit area 1,800 kg/m² (- 5 %) Nominal thickness 1,6 mm (- 10 %) Length 12,0 m (- 1 %) Width 1,0 m (± 1 %) Straightness max deviation 20 mm/10 m Pass Visual defects No defects Pass 3. Intended use or uses of the construction product: 2015-05-28 Version: Test method EN 1849-1 EN 1849-1 EN 1848-1 EN 1848-1 EN 1848-1 EN 1850-1 1 6. AVCP-class EN 13859-1 :2010 Underlays for discontinuous roofing 3 4. Name, registered trade name or registered trade mark and contact address of the manufacturer : KATEPAL OY, P.O.Box 33, FI-37501 Lempäälä, Finland, Tel: +358 3 375 9111, Fax: +358 3 375 0974, www.katepal.fi, E-mail: katepal@katepal.fi 5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12(2): 7. In case of the declaration of performance concerning a construction product covered by a harmonised standard In case of AVCP 3 The notified testing laboratory VTT Expert Services No. 0809 has carried out the determination of the product type on the basis of type-testing (based on sampling carried out by the manufacturer), type calculation, tabulated values or descriptive documentation of the product 8. In case of the declaration of performance concerning a construction product covered by a european technical approval (ETA): 9. Declared performance not valid for this product FIRE PROPERTIES External Fire performance 1) Reaction to Fire Fireclass Broof(t2) E Classification EN 13501-5 EN 13501-1 Test method ENV 1187 (t2) EN ISO 11925-2 ESSENTIAL CHARACTERISTICS Harmonised technical specification: Watertightness under pressure Resistance to water penetration EN 13859-1: 2010 - W1 (200 mm) Tolerance Units - Test Method EN 1928 A EN 1928 A Tensile strength at 23 °C longitudinal transversal Elongation at maximum force longitudinal transversal 600 - 20 % 500 - 20 % > 30 > 30 N/50 mm N/50 mm % % EN 12311-1 EN 12311-1 Resistance to tearing longitudinal transversal Flexibility at low temperature upper surface bottom surface Ø 30 mm Ø 30 mm DURABILITY AFTER AGEING 250 - 20 % 250 - 20 % -25 -25 EN 12310-1 N N EN 1109 °C °C Resistance to water penetration after ageing Tensile stregth (longitudinal) after ageing Tensile stregth (transversal) after ageing Elongation at max.force (longit.) after ageing Elongation at max.force (transv.) after ageing NPD NPD NPD NPD NPD N/50 mm N/50 mm % % EN 13859-1 EN 13859-1 EN 13859-1 EN 13859-1 EN 13859-1 DANGEROUS SUBSTANCES NPD Note 1: This product does not contain asbestos or tar constituents Note 2: In the absence of European harmonized test methods, verification and declaration on release/content has to be done taken into account national provisions in the place of use. NPD = no performance determined OTHER CHARACTERISTICS ACCORDING TO: EN 13859-1 Tolerance Units Test Method Water vapour transmission properties Dimensional stability 0,8 x 10e12 -0,2 m*m*s*Pa/kg EN 1931 % EN 1107-1 10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9. This declaration of performance is issued under the sole responsibility of the manufacturer indentified in point 4. Signed for and on behalf of the manufacturer by: Lempäälä 2015-05-28 Mikko Pellinen / Managing director The manufacturer reserves the right to change the content without further notice. Version: Updated: 1 05/2015
Download PDF fil